Brands

Features 60,000 PSI ductile iron construction with straight-pull screw design 3 sets of replaceable hardened steel jaws: parallel serrated, pipe, ...

Features 65,000 PSI tensile ductile iron body construction Interlocking 360° swivel base with two lockdowns Hardened, replaceable steel pipe jaws,...

These diamond-impregnated replacement wheels are for the Eastwood TG1800 corded and TG2000 cordless tungsten grinders. Each wheel is double-sided, ...

This 6-pack of diamond-impregnated grinding wheels keeps your Eastwood tungsten grinder stocked for the long haul. Each wheel is double-sided, deli...

The Eastwood Panel Prep Butt Weld Clamp forms a precise 0.062-inch, 45-degree beveled flange on sheet metal edges before you MIG or TIG weld a butt...

The Eastwood Pneumatic Panel Prep Tool creates the same 0.062-inch, 45-degree beveled flange as the manual version, but with air power behind each ...

This is a replacement return fitting assembly for the Eastwood Elite TIG Torch Water Cooler (item 55252). It replaces the fitting that connects the...

The Rockwood TIG Foot Pedal gives you hands-free, variable amperage control while welding, letting you ramp current up or down mid-weld instead of ...

The Strong Hand Tools Utility Clamp is built for fast setup on fabrication and fixturing work, locking into position roughly 10 times faster than a...

The Strong Hand Tools Utility Clamp is built for fast setup on fabrication and fixturing work, locking into position roughly 10 times faster than a...

The Strong Hand Tools Utility Clamp is built for fast setup on fabrication and fixturing work, locking into position roughly 10 times faster than a...

The Strong Hand Tools 4-in-1 Utility Clamping System packages a sliding arm clamp with an extender block and V-pad into one kit, giving you multipl...

The Strong Hand Tools Strong Grip Pipe Pliers combine a fixed top jaw with a 1.5-inch swivel pad and an adjustable V-pad on the bottom jaw, letting...

The Strong Hand Tools Drill Press Clamp is built for quick lock and release, making it a practical choice for repetitive clamping on a drill press ...

The Strong Hand Tools PG622V Pipe Pliers use two fixed V-pads instead of a swivel/flat jaw combination, giving both jaws a matched clamping surface...

Strong Hand Tools Pipe Pliers hold round or square tube steady for butt-welding, with an opening range from 1/4 inch up to 3 inches (6.4 to 76mm) t...

The Strong Hand Tools JointMaster Pliers are a single-hand corner clamping tool designed to hold stock at a right angle while you tack or permanent...

The Strong Hand Tools Pipe Alignment Clamp uses a quick-acting lever instead of a slow-turning screw for the initial clamp, then a screw that glide...

The Strong Hand Tools WAC45 is a machined cast iron angle clamp built to hold two axes of a fixture or frame joint square while you tack and weld. ...

The Strong Hand Tools Adjust-O Dual Switch Magnet is a 90-degree welding square rated at 265 lbs (120 kg) pull force, built to hold flat and round ...

The Strong Hand Tools Adjust-O Angle Magnet adjusts from 30 to 275 degrees, giving you a single magnetic fixture that covers a wide range of joint ...

Features 60mm low-profile height for tight, hard-to-reach areas Light-duty holding of stock at multiple points for accurate fixturing on odd-shape...

Features 43" x 15.75" zinc-plated tabletop resists corrosion and provides a conductive welding surface 500 lb load capacity 5/8" fixturing holes s...

Features Fits Eastwood TIG200 AC/DC and DC, MP200i, and Versa-Cut 20/40/60 200 amp rated 10-25 twist-lock DINSE connector 5 gauge wire Includes gr...